Foam Roofing using Sprayed Polyurethane Foam

Foam Roofing Using SPRAYED POLYURETHANE FOAM (SPF)

The Sprayed Polyurethane Foam Roofing System’s superiority is in its “closed cell” combination of properties that, when spray applied, forms a monolithic barrier against water entry. As a self-flashing system, it eliminates seams and joints, along with the need for fasteners, strips and heavy ballasts that can lower a roof’s resistance to high winds. It even eliminates standard trouble spots along roof-mounted units, penetrations, curbs and parapets where flashings can fail.

Nothing hits your overhead like a leaky roof. In addition to unbudgeted roof repairs, it can damage a building’s contents and even deteriorate a structure’s stability. Taylor's Industrial Roof Coatings, Inc's Sprayed Polyurethane Foam (SPF) Roof System doesn’t just stop leaks – it also prevents them. By eliminating water entry points, Taylor's SPF Roof System provides peace of mind and protects your overhead.

• Foam Insulation • Foam Roofings • Poly-Sil 2200 • Polyurea • Silver Bullet • Metal Roof Restoration •
Taylor's Industrial Coatings Inc., 108 Dr. JA Wiltshire Ave. E, Lake Wales, Florida 33853
Call: (863) 676-5093 1-800-932-3049 FAX (863)-676-9573

The Ultimate Roof Solution
The Roof-Tek® Sprayed Polyurethane Foam Roof System provides multifaceted protection for your building... and your overhead.

LEAK PROOF
Want a low maintenance roof, free of leaks and repairs? Because it’s seamless, the Roof-Tek® self-flashing system gets rid of water entry points and costly repairs.

LIGHTWEIGHT
The Roof-Tek® Roof System is 20 times lighter than a conventional built-up roof of the same thickness, making it the perfect choice for long spans or installation over existing roofs without any additional structural reinforcement.

COST EFFECTIVE
With an application process that is quick, quiet and requires less laborers, the Roof-Tek® Roof System is exceptionally friendly to those who work in and visit your building. It can be applied over most existing roofs, so there’s no costly roof removal or work shutdown. It’s practically maintenance-free, and has an extended service life.

WEATHERPROOF
The weather-resistant Roof-Tek® Roof System protects against extremes in temperature, rain, snow, wind and ultraviolet radiation. If a puncture is made in the system’s membrane, water is restricted to the hole and does not spread to interior insulation or cause interior leaks. (In most cases, the only repair tool needed is a tube of caulk.)

ENERGY SAVING
Roof-Tek’s® polyurethane foam is lightweight and the most efficient insulation available. With savings up to 50% on heating and cooling costs, the new roof will quickly pay for itself.

ENVIRONMENTALLY FRIENDLY
No tear-off requirements means no landfill. A reflective coating and high R-value mean better environmental responsibility with lower environmental impact.

QUALITY ASSURED
Roof-Tek® offers the most comprehensive warranty program available and professional installation by properly trained application experts.
 

COMPARING ROOF SYSTEMS

BUILT-UP MEMBRANE
• Requires overhangs, overlap seams and joints
• Attached flashings
• Secured to deck with fasteners
• Subject to heavy damage and penetration from flying debris
• Faces lift-off and peeling from high winds
• Failure exposes building’s interior to leaks and water damage

ROOF-TEK® SPF ROOF SYSTEM
• Self-flashing, continuous smooth surface with no seams or joints
• 100% adhesion without fasteners
• Sturdy and resistant against penetration from flying debris
• Grips walls and holds tight against high winds
• Successfully protects the building’s interior from leaks and water damage
• Energy Star, CRRC, U.L. and F.M. approved

PROTECTIVE COATING

PHYSICAL PROPERTIES

ACRY-TEK 4200 SERIES

POLY-SIL 2200 SERIES

SILVER BULLET®
Tensile Strength 250 PSI 500 PSI 1600 PSI
Elongation 300% 150% 300%
Permeability 3.0 perms 3.9 perms 0.025 perms
Hardness 50 Shore A 50 Shore A 90 Shore A
Solids by Volume 60% 65% 96%
Flash Point >212 degrees F >105 degrees F >200 degrees F
Weatherability No degradation No degradation Slight chalking
Cure Time 4-8 hours 2-8 hours 2-10 minutes
Drying Time 1 hour 1 hour N/A

Is a leaky roof affecting your bottom line? Does it have the potential to? Roof-Tek® can’t control the weather, but it can prevent what it would do to your overhead. To learn more about the benefits of the Roof-Tek® Sprayed Polyurethane Foam Roof System, call Taylor's Industrial Coatings Inc.at 1-800-932-3049

Taylor's Industrial Coatings Inc., 108 Dr. JA Wiltshire Ave. E, Lake Wales, Florida 33853
Contact us at: (863) 676-5093 1-800-932-3049 FAX (863)-676-9573
Owner: Greg Taylor gjtaylor1950@hotmail.com cellphone: (863) 528-4500
Owner: Scott Taylor scotttaylor81@hotmail.com cellphone: (863) 528-4502
Sales: Scott McRae scott.mcrae@verizon.net cellphone: (863) 528-4513

Foam Roofing SPF Application Pictures

The Foam Roofing ExpertsTaylor's Industrial Coatings Inc.
108 Dr. JA Wiltshire Ave. E, Lake Wales, Florida 33853
Call:(863) 676-5093 1-800-932-3049 FAX (863)-676-9573
Owner: Greg Taylor gjtaylor1950@hotmail.com cellphone: (863) 528-4500
Owner: Scott Taylor scotttaylor81@hotmail.com cellphone: (863) 528-4502
Sales: Scott McRae scott.mcrae@verizon.net cellphone: (863) 528-4513

Foam Insulation using Sprayed Polyurethane Foam Insulation
Sprayed Polyurethane Foam Roofing has been successfully used for over 30 years. Foam roofing is lighter than tar gravel roofs and Sprayed Polyurethane Foam Roofs have no seams or joints. Sprayed Polyurethane Foam Roofing installed by Taylor's Industrial Coatings can also be used for Metal Roof Restoration, and comes with 10 year Warranted Maintenance, providing savings and durability. Taylor's proven Foam Roofing and Foam Insulation Systems are listed under UL 790 and UL 723: UL 790 roofing systems are listed Class A over non-combustible decks and Class B over combustible decks.